French Drain Gravel and Pipe: How Much You Need and How to Lay It Out
How to size the trench, choose the stone, and work out how many tons of gravel and feet of pipe a French drain needs, with a fully worked 50-foot example.
By Kadir C. · Published October 24, 2026 · 8 min read
A French drain is a simple idea: a sloped trench filled with clean stone, usually with a perforated pipe at the bottom, that gives groundwater an easier path than the one it is currently taking into your basement or across your lawn. Most of the cost and most of the labor is in the stone, so getting the gravel quantity right is the single most useful number to work out before you call a supplier.
This guide explains how the trench size drives the gravel quantity, why you subtract the pipe and the soil cap, how to convert cubic yards to the tons a quarry will quote, and how much fabric and fall you need. A full worked example for a 50-foot drain is in the middle.
1. Decide the trench size first
Everything else follows from three dimensions: length, width, and depth.
- Length runs from the wettest point to wherever the water can leave the property safely: a daylight outlet on lower ground, a dry well, or another approved discharge point. Measure along the actual route, not in a straight line.
- Width for a typical residential drain is 8 to 12 inches. A narrow trenching shovel gives you about 6 inches; a rented trencher usually cuts 6 to 8 inches. Wider trenches move more water but cost more stone.
- Depth is commonly 18 to 24 inches for yard drainage. Drains intended to intercept water before it reaches a foundation are often deeper, but foundation drainage is a job where a contractor's site assessment is worth paying for.
Before digging anywhere in the U.S., call 811 or use your state's online request. Utility locating is free and buried gas and electric lines are often shallower than people expect.
2. Plan the slope (the "fall")
Water in a French drain moves by gravity, so the trench bottom must slope continuously toward the outlet. A common minimum is a 1% grade, which is about 1/8 inch of drop for every foot of length. A 2% grade (about 1/4 inch per foot) drains faster and tolerates small mistakes during digging better.
| Drain length | Total drop at 1% | Total drop at 2% |
|---|---|---|
| 25 ft | 3 in | 6 in |
| 50 ft | 6 in | 12 in |
| 100 ft | 12 in | 24 in |
Because the drop accumulates, a long drain on flat ground ends up much deeper at the outlet than at the start. If that end depth is impractical, consider two shorter drains with separate outlets.
3. Work out the gravel volume
The stone fills the trench except for two things that take up room: the pipe, and any soil or sod you put back on top.
- Gravel depth = trench depth minus the soil cap. If you want grass to grow over the drain, leave roughly 3 to 4 inches for topsoil and sod. If the stone stays exposed at the surface, there is no cap.
- Gravel zone volume (cubic feet) = length × width (ft) × gravel depth (ft).
- Pipe volume (cubic feet) = π × radius² × length. A 4-inch pipe has a 2-inch (0.167 ft) radius, so it occupies about 0.087 cubic feet per foot of run. A 6-inch pipe occupies about 0.196 cubic feet per foot.
- Net gravel = gravel zone volume − pipe volume.
- Add waste. Stone settles, trench walls are never perfectly straight, and some always ends up in the grass. 10% is a sensible allowance.
- Convert: cubic yards = cubic feet ÷ 27. Quarries usually sell by the ton; clean crushed stone weighs roughly 1.3 to 1.5 tons per cubic yard depending on the rock type. Our calculator uses 1.4.
Worked example: a 50-foot yard drain
A 50 ft drain, 12 inches wide and 18 inches deep, with a 4-inch perforated pipe and a 4-inch topsoil-and-sod cap so the lawn grows back over it.
- Gravel depth: 18 − 4 = 14 in = 1.167 ft
- Gravel zone: 50 × 1.0 × 1.167 = 58.3 cu ft
- Pipe: 3.1416 × 0.167² × 50 ≈ 4.4 cu ft
- Net gravel: 58.3 − 4.4 = 53.9 cu ft
- With 10% waste: 53.9 × 1.10 ≈ 59.4 cu ft
- Cubic yards: 59.4 ÷ 27 ≈ 2.2 cubic yards
- Weight at 1.4 t/yd³: ≈ 3.1 tons
- Topsoil cap: 50 × 1.0 × 0.333 ≈ 16.7 cu ft ≈ 0.6 cubic yards (often you can reuse excavated soil)
- Fall at 1%: 6 inches from the high end to the outlet
For comparison, 3 tons of stone in 50 lb bags would be about 120 bags. For anything beyond a very short drain, bulk delivery is far cheaper and saves a lot of lifting.
4. Choose the right stone
The stone must leave open space between pieces for water to move through. That means clean, washed stone with no fine particles. Crushed angular stone around 3/4 inch to 1 inch (often sold as "#57 stone" in many U.S. regions) is the most common choice; it locks together so the trench does not shift, while still leaving plenty of voids. Avoid:
- Crusher run, "road base," or anything with dust or fines. These are designed to compact into a dense layer, which is the opposite of what a drain needs.
- Very small pea gravel right against a perforated pipe, where it can work into the slots. Pea gravel is fine as a decorative top layer.
Names and size numbers vary between suppliers, so describe what you need ("clean washed 3/4-inch crushed stone for a drain") rather than relying on a number alone.
5. Pipe and fabric
Pipe
You need one foot of perforated pipe per foot of trench, plus solid (non-perforated) pipe for any section that only carries water away without collecting it, such as a run under a driveway to the outlet. Rigid perforated PVC is easier to keep on an even slope and to clean out; corrugated pipe is cheaper and quicker to lay. A common practice is to install perforated pipe with the holes facing down, so water rises into the pipe from below rather than carrying sediment in from above. Follow the instructions for the specific product you buy.
Filter fabric
A non-woven geotextile fabric lining the trench keeps surrounding soil from washing into the stone and clogging it over the years. To wrap the stone fully, the fabric must be wide enough to cover the bottom, run up both sides, and overlap on top. A simple rule: fabric width = trench width + 2 × trench depth + about 12 inches of overlap. For the 12 × 18-inch trench above, that is 12 + 36 + 12 = 60 inches, so a 5-foot roll fits well. Add about 5% to the length for overlaps where rolls join.
6. Common mistakes that make a drain fail
- No real outlet. A trench that slopes to a low spot with nowhere to go is a buried pond. Make sure the outlet is lower than every point of the pipe.
- Flat spots or reverse slope. Check the trench bottom with a level and a straight board, or a string line, before adding stone.
- Dirty stone. Fines clog the voids quickly. Pay the small premium for washed stone.
- Discharging onto a neighbor's property or a street where it is not allowed. Many municipalities regulate where drainage water can go; check before you dig.
- Treating a foundation leak as a yard project. Water entering through basement walls can have several causes. A drain may help, but it is worth getting the cause diagnosed first.
Quick reference
| Item | How to estimate |
|---|---|
| Gravel | (length × width × gravel depth − pipe volume) × 1.10, ÷ 27 for cubic yards |
| Tons | Cubic yards × about 1.4 (ask your supplier for their stone's figure) |
| Perforated pipe | Equal to the collecting length of trench |
| Fabric | Width: trench width + 2 × depth + 12 in. Length: trench length + 5% |
| Fall | At least 1/8 in per foot (1%); 1/4 in per foot (2%) is more forgiving |
This guide is general information for typical residential projects, not professional engineering or legal advice. Product specifications and local codes vary; check your product label and your local building department. Found an error? Email contact@yardcraftcalc.com.